
Skin Fittings Long - Domed
TruDesign Long Skin Fittings comply to ISO 9093-2. and ABYC H-27 500Lb Standard (when used with ABYC Collar)
Designed and made in New Zealand, the Skin Fitting body and nut are moulded from a glass-reinforced nylon composite. High strength, high-modulus glass fibres provide dramatic strength, stiffness, toughness and dimensional stability. These properties allow a significant weight reduction over metallic fittings.
TruDesign Skin Fittings eliminate the corrosion and electrical bonding problems associated with metallic fittings.
When used in below waterline applications, a Ball Valve should be directly connected and installed as per manufacturers instructions for safety and compliance to relevant marine standards.
Documents
Features
- Manufactured from a glass-reinforced nylon composite - High strength and light weight
- Compatible with all hull types - Can be used on aluminium, steel, wood or GRP hulls up to 100mm thick
- Immune to corrosion and electrolysis - Long life with no concerns over decreased performance due to corrosion
- Chemical resistant - Impervious to diesel, petrol and antifouling paints
- UV resistant - Will not degrade or discolour with ultraviolet light from the sun
- High quality surface finish - Will not discolour with green film as similar bronze fittings do
- Paintable - Can be painted with all types of antifouling
- Limited Warranty
- TruDesign accepts no responsibility for Ball Valves or Skin Fittings which are not installed as per manufacturers instructions.
Frequently Asked Questions
How do I replace an old Skin Fitting (Thru Hull) with TruDesign?
Replacing an old metallic skin fitting with TruDesign is relatively simple - follow the instructions contained in in the below Technical Information Sheet.
What sealant can I use on TruDesign threads ?
Thread sealing options: - 3M 5200 - 3M 5200FT (fast cure) - Sikaflex 291i - Sikaflex 591 - Loctite 5331 - Loctite 55 Pipe Sealing Chord - PTFE Thread Tape
How to use the TruDesign Skin Fitting / Thru Hull Install Tool?
Using the TruDesign Install Tool allows one person to fit Skin Fittings (thru Hulls) without the need for a "helper" inside the boat at the same time. Marine adhesive sealants such as 3M Fast Cu...
Identification of threads BSP or NPS ?
Tru-Design manufacture these marine fittings with two types of threads: BSP British Standard Pipe for the European market. NPS National pipe straight for the US market. Each threaded fitting wi...
Are TruDesign Skin Fittings certified ?
ISO 9093-2. - TruDesign ¾”, 1”, 1¼”, 1½”, 2” and 3” Thru Hull’s, Ball Valves and Tail assemblies comply with ISO 9093-2 certification. The ½” does not comply. ABYC 500Lb load test standard. TruD...
What sealant should I use between a bronze or stainless skin fitting and a TruDesign ball valve ?
The same options as you would use for sealing any TruDesign composite fitting to a TruDesign composite Ball Valve: #3M 5200 #3M 5200 FT (Fastcure) # Sikaflex 291 # Sikaflex 591 # Loctite 5...
Do you have an overview of your products?
Yes we made a video to show how our products work, we hope you find it helpful.
Models

91077
Skin Fitting Long ¾" BSP Domed

91078
Skin Fitting Long 1" BSP Domed

91079
Skin Fitting Long 1¼" BSP Domed

91080
Skin Fitting Long 1½" BSP Domed

91148
Skin Fitting Long ¾" BSP Domed

91149
Skin Fitting Long 1" BSP Domed

91150
Skin Fitting Long 1¼" BSP Domed

91151
Skin Fitting Long 1½" BSP Domed