Manual Aquavalve

the most versatile Y-valve on the market today

4060721a2adabdaf2ae9ce5ad8222180 full

Manual Aquavalve

The TruDesign Aquavalve (Y valve) is designed and made in New Zealand

Legislation in many countries dictates the use of holding tanks near shore, or in defined areas. By installing a diverting valve (Y Valve), the user has the choice to divert black water to a holding tank or directly overboard when circumstances allow.


Download Info Sheet

Features

  • Manufactured from a glass reinforced nylon composite - High strength and light weight.
  • Stainless steel fasteners - Will not corrode in salt laden air.
  • Easy installation - With a range of straight, 90° and 120° tails, and two seal options, plumbing in confined spaces is made easy.
  • Handle position lockable - Legislation in some regions require the overboard discharge handle to be locked into the holding tank position when in ‘no discharge’ zones
  • Available in black or white - Fits in with colour schemes in plumbing areas allowing easy identification of components.
  • Pressure tested - All valves are pressure tested to ensure quality and safety in respect to sealing and operation.
  • Silicon seal - The Aquavalve® is the only valve on the market today with smooth movement and an excellent seal with good wear resistance.
  • Composite spanner included - Avoids using pipe wrenches that gouge the fitting. Facilitates access in tight places.
  • Fascia plate on standard model can be removed to reveal simple “open - open - inlet” labeling - Where product is not used for marine toilets, all toilet references are removed.
  • Large operating temperature range - Suitable for all marine environments, from -40°C to +110°C
  • Note bulkhead hole diameter for Aquavalve through Bulkhead is 49.0mm

Frequently Asked Questions

  • How to service the Manual Aquavalve

    If your Aquavalve has not had the handle turned for over 12 months the chances are that the valve can become tight to turn or even jammed in the case of very high salt build up. Tools required: Philips screw driver, felt pen, rubber gloves, bucket & towels. Step 1: Mark the top face of the printed plate with a felt pen so it goes back on the same way as this plate has reverse printing on the other side. Step 2: Unscrew the two screws on the printed plate and remove this plate. Step 3: Mark the next plate which has printed OPEN & INLET and the body so it can be put back in the same position Step 3: Unscrew the three screws on the face plate but before trying to remove the rotor have a bucket or old towels close to stop any liquid that may be in the pipes. Step 4: Grab hold of the handle and turn and pull the handle, with the attached rotor and seals, out of the body. Step 5: With the rotor and seal removed clean out the body where the seal fits. Step 6: Take the curved seal off the rotor pad and clean it in hot water (use of rubber gloves advised). Step 7: Fit the cleaned seal back on the rotor pad then assemble this on the rotor. Step 8: Grease the curved seal with silicone grease and the O-ring in the body and assemble the rotor into the body by turning while pushing the rotor in place. Line up the felt pen marks on the printed plate and screw in the 3 screws - do not over tighten! Step 9: Fit the printed plate back on in its original position with pen mark and screw in the 2 screws. The Aquavalve should now turn freely and providing it is turned every month or two will work fine for over 12 months. We suggest yearly servicing and in the case of a damaged seal there is a seal kit (part number 90316) available.

Models

E93590fef3696793686c7f1e63bd2022 grid
Manual Aquavalve

90312

Aquavalve black

956d5197d02d996880bfb223aaf01b3f grid
Manual Aquavalve

90314

Aquavalve white

F20ebc6a9b2446a76a165abd13d3abdf grid
Manual Aquavalve

90313

Aquavalve through bulkhead

Ef70c76249f6241bf6021e5cc64da3ce grid
Manual Aquavalve

90453

Extention Pack Through Bulkhead